Search results
In physics and engineering, the time constant, usually denoted by the Greek letter (tau), is the parameter characterizing the response to a step input of ... more
In physics and engineering, the time constant, usually denoted by the Greek letter (tau), is the parameter characterizing the response to a step input of ... more
In signal processing, control theory, electronics, and mathematics, overshoot is the occurrence of a signal or function exceeding its target. It arises ... more
Time-domain reflectometry or TDR is a measurement technique used to determine the characteristics of electrical lines by ... more
In 1954, Miles developed his version of this equation for GRMS as he was researching fatigue failure of aircraft structural ... more
For the root mean square value of the ripple voltage, the calculation is more involved as the shape of the ripple waveform has a bearing on the result. ... more
A stepper motor or step motor or stepping motor is a brushless DC electric motor that divides a full rotation into a number of equal steps. The ... more
In optics, Miller’s rule is an empirical rule which gives an estimate of the order of magnitude of the nonlinear coefficient.
More formally, ... more
In microwave and radio-frequency engineering, a stub or resonant stub is a length of transmission line or waveguide that is connected at one end only. The ... more
In microwave and radio-frequency engineering, a stub or resonant stub is a length of transmission line or waveguide that is connected at one end only. The ... more
In electronics, gain is a measure of the ability of a two-port circuit (often an amplifier) to increase the power or amplitude of a signal from the input ... more
Damping is an influence within or upon an oscillatory system that has the effect of reducing, restricting or preventing its oscillations.( The neper ... more
In electronics, gain is a measure of the ability of a two-port circuit (often an amplifier) to increase the power or amplitude of a signal from the input ... more
In electronics, gain is a measure of the ability of a two-port circuit (often an amplifier) to increase the power or amplitude of a signal from the input ... more
In electrical and electronic systems, reactance is the opposition of a circuit element to a change of electric current or voltage, due to that ... more
The series RLC can be analyzed for both transient and steady AC state behavior using the Laplace transform. If the voltage source ... more
It is defined as the peak energy stored in the circuit divided by the average energy dissipated in it per cycle at resonance; Q factor is directly ... more
A brushed DC motor is an internally commutated electric motor designed to be run from a direct current power source. Brushed motors were the first ... more
The power factor of an AC electrical power system is defined as the ratio of the real power flowing to the load, to the apparent power in the circuit. In a ... more
Electrical impedance is the measure of the opposition that a circuit presents to a current when a voltage is applied. The term complex impedance may be ... more
Self-inductance is the voltage produced by the changing of the electric current through a circuit that contains inductance, which opposes the change in ... more
Mutual inductance is the voltage produced by the changing of the electric current through a circuit that contains inductance, which opposes the change in ... more
An LC circuit, also called a resonant circuit, tank circuit, or tuned circuit, is an electric circuit consisting of an inductor, represented by the letter ... more
An LC circuit, also called a resonant circuit, tank circuit, or tuned circuit, is an electric circuit consisting of an inductor, represented by the letter ... more
In classical electromagnetism, polarization density is the vector field that expresses the density of permanent or induced electric dipole moments in a ... more
Permeability is the measure of the ability of a material to support the formation of a magnetic field within itself. In other words, it is the degree of ... more
Electrical impedance is the measure of the opposition that a circuit presents to a current when a voltage is applied. The term complex impedance may be ... more
Electrical impedance is the measure of the opposition that a circuit presents to a current when a voltage is applied. The term complex impedance may be ... more
A resistor–capacitor circuit (RC circuit), or RC filter or RC network, is an electric circuit composed of resistors and capacitors driven by a voltage or ... more
...can't find what you're looking for?
Create a new formula