Search results
A cantilever is a beam anchored at only one end. The beam carries the load to the support where it is forced against by a moment and shear stress. A ... more
A cantilever is a beam anchored at only one end. The beam carries the load to the support where it is forced against by a moment and shear stress. A ... more
A cantilever is a beam anchored at only one end. The beam carries the load to the support where it is forced against by a moment and shear stress. A ... more
A cantilever is a beam anchored at only one end. The beam carries the load to the support where it is forced against by a moment and shear stress. A ... more
In engineering, deflection is the degree to which a structural element is displaced under a load.
The elastic deflection of a beam, loaded at its
... more
Elastic deflection is the degree to which a structural element is displaced under a load.
The deflection at any point, along the span of a center
... more
In Applied mechanics, bending (also known as flexure) characterizes the behavior of a slender structural element subjected to an external load applied ... more
In engineering, deflection is the degree to which a structural element is displaced under a load.
The maximum elastic deflection on a beam supported
... more
An I-beam, also known as H-beam, W-beam (for “wide flange”), Universal Beam (UB), Rolled Steel Joist (RSJ), or ... more
An I-beam, also known as H-beam, W-beam (for “wide flange”), Universal Beam (UB), Rolled Steel Joist (RSJ), or ... more
In engineering, deflection is the degree to which a structural element is displaced under a load.
The elastic deflection of a weightless cantilever
... more
In engineering, deflection is the degree to which a structural element is displaced under a load. It may refer to an angle or a distance.
The angle of
... more
In engineering, deflection is the degree to which a structural element is displaced under a load. The deflection at any point along the span of an end ... more
Euler–Bernoulli beam theory (also known as engineer’s beam theory or classical beam theory) is a simplification of the linear theory of elasticity ... more
In engineering, deflection is the degree to which a structural element is displaced under a load. It may refer to an angle or a distance.
The angle of
... more
A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, ... more
Euler–Bernoulli beam theory (also known as engineer’s beam theory or classical beam theory) is a simplification of the linear theory of elasticity ... more
Elastic deflection is the degree to which a structural element is displaced under a load.
The deflection, at the free end, of a cantilevered beam
... more
In engineering, deflection is the degree to which a structural element is displaced under a load.
This maximum deflection occurs at a distance x_1
... more
In engineering, deflection is the degree to which a structural element is displaced under a load. The deflection at any point along the span of a uniformly ... more
The blade root bending moment due to the wind turbine yaw operation. The yaw rate can be calculated for passive yaw, or is defined by the design for active ... more
The shaft bending moment due to yaw depends on the blades of the rotor. In this case the rotor has 2 blades
... more
Column or pillar in architecture and structural engineering is a structural element that transmits, through compression, the weight of the structure above ... more
Shear stress,is defined as the component of stress coplanar with a material cross section. The average shear stress is force per unit area. Beam shear is ... more
Column or pillar in architecture and structural engineering is a structural element that transmits, through compression, the weight of the structure above ... more
A bimetallic strip is used to convert a temperature change into mechanical displacement. The strip consists of two strips of different metals which expand ... more
All wind turbines operate with a yaw error. In this case an extreme yaw error of 30 degrees is assumed. The flapwise blade root bending moment due to that ... more
A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, ... more
In physics and applied mathematics, the mass moment of inertia, usually denoted by I, measures the extent to which an object resists rotational ... more
Bending is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials, most commonly sheet ... more
...can't find what you're looking for?
Create a new formula