Search results
According to Hooke’s Law, Elastic potential energy is stored in a simple harmonic oscillator at position x,for example, the energy saved in an object ... more
A spring is an elastic object used to store mechanical energy. Springs are usually made out of spring steel. Small springs can be wound from pre-hardened ... more
Hooke’s law is a principle of physics that states that the force F needed to extend or compress a spring by some distance X is proportional to that ... more
When a force is applied on a spring, and the length of the spring changes by a differential amount dx, the work done is Fdx. For linear elastic springs, ... more
A harmonic oscillator is a system that, when displaced from its equilibrium position, experiences a restoring force, proportional to the displacement. If a ... more
Hooke’s law states that the force needed to extend or compress a spring by some distance is proportional to that distance.The stresses and strains ... more
In lead climbing using a dynamic rope, the fall factor (f) is the ratio of the height (h) a climber falls before the climber’s rope begins to stretch ... more
The simple harmonic motion is a type of periodic motion where the restoring force is directly proportional to the displacement. The frequency of a simple ... more
In mechanics and physics, simple harmonic motion is a type of periodic motion where the restoring force is directly proportional to the displacement. It ... more
Stress is a physical quantity that expresses the internal forces that neighboring particles of a continuous material exert on each other. Any strain ... more
Torsion balances, torsion pendulums and balance wheels are examples of torsional harmonic oscillators that can oscillate with a rotational motion about the ... more
Formula first contributed by:
trooper
In engineering, the damping ratio is a dimensionless measure describing how ... more
Leaf spring, commonly used for the suspension in wheeled vehicles. The term is also used to refer to a bundled set of leaf springs. As the spring flexes, ... more
In continuum mechanics, stress is a physical quantity that expresses the internal forces that neighbouring particles of a continuous material exert on each ... more
Damped harmonic motion is a real oscillation, in which an object is hanging on a spring. Because of the existence of internal friction and air resistance, ... more
Damped harmonic motion is a real oscillation, in which an object is hanging on a spring. Because of the existence of internal friction and air resistance, ... more
In 1954, Miles developed his version of this equation for GRMS as he was researching fatigue failure of aircraft structural ... more
Contact mechanics is the study of the deformation of solids that touch each other at one or more points. When two solid surfaces are brought into close ... more
In computer architecture, Amdahl’s law (or Amdahl’s argument) is a formula which gives the theoretical speedup in latency of the execution of a ... more
A simple harmonic motion is a type of periodic motion where the restoring force is directly proportional to the displacement. The motion is sinusoidal in ... more
A simple harmonic motion is a type of periodic motion where the restoring force is directly proportional to the displacement. The motion is sinusoidal in ... more
A mechanical equilibrium is a state in which a momentum coordinate of a particle, rigid body, or dynamical system is conserved. Usually this refers to ... more
A harmonic oscillator is a system that, when displaced from its equilibrium position, experiences a restoring force, proportional to the displacement. If a ... more
In science, buckling is a mathematical instability that leads to a failure mode.
When a structure is subjected to compressive stress, buckling may ... more
The Van 't Hoff equation in chemical thermodynamics relates the change in the equilibrium constant, Keq, of a chemical equilibrium to the change in ... more
(a) The figure shows the forearm of a person holding a book. The biceps exert a force FB to support the weight of the forearm and the book. The triceps are assumed to be relaxed. (b) Here, you can view an approximately equivalent mechanical system with the pivot at the elbow joint
Strategy
There are four forces acting on the forearm and its load (the system of interest). The magnitude of the force of the biceps is FB, that of the elbow joint is FE, that of the weights of the forearm is wa , and its load is wb. Two of these are unknown FB, so that the first condition for equilibrium cannot by itself yield FB . But if we use the second condition and choose the pivot to be at the elbow, then the torque due to FE is zero, and the only unknown becomes FB .
Solution
The torques created by the weights are clockwise relative to the pivot, while the torque created by the biceps is counterclockwise; thus, the second condition for equilibrium (net Ï„ = 0) becomes
Note that sin θ = 1 for all forces, since θ = 90º for all forces. This equation can easily be solved for FB in terms of known quantities,yielding. Entering the known values gives
which yields
Now, the combined weight of the arm and its load is known, so that the ratio of the force exerted by the biceps to the total weight is
Discussion
This means that the biceps muscle is exerting a force 7.38 times the weight supported.
Reference : OpenStax College,College Physics. OpenStax College. 21 June 2012.
http://openstaxcollege.org/textbooks/college-physics
Creative Commons License : http://creativecommons.org/licenses/by/3.0/
Column or pillar in architecture and structural engineering is a structural element that transmits, through compression, the weight of the structure above ... more
Sound pressure or acoustic pressure is the local pressure deviation from the ambient (average, or equilibrium) atmospheric pressure, caused by a sound ... more
In science, buckling is a mathematical instability that leads to a failure mode.
When a structure is subjected to compressive stress, buckling may ... more
Young’s modulus, also known as the Tensile modulus or elastic modulus, is a measure of the stiffness of an elastic isotropic material and is a ... more
...can't find what you're looking for?
Create a new formula
Calculate the force the biceps muscle must exert to hold the forearm and its load as shown in the figure below, and compare this force with the weight of the forearm plus its load. You may take the data in the figure to be accurate to three significant figures.