'

Search results

Found 1043 matches
Load and Resistance Factor Design (LRFD) - Load combinations (eq2)

In structural engineering, a structure is a body or combination of pieces of rigid bodies in space to form a fitness system for supporting loads. ... more

Magnification of the lens

Converging lens in air will focus a collimated beam travelling along the lens axis to a spot (known as the focal point) at a distance “f” from ... more

Free-fall time (Infall of a spherically-symmetric distribution of mass)

The free-fall time is the characteristic time that would take a body to collapse under its own gravitational attraction, if no other forces existed to ... more

Torsion constant (Rectangle)

In solid mechanics, torsion is the twisting of an object due to an applied torque. The torsion constant is a geometrical property of a bar’s cross-section ... more

Hyperboloid of one sheet equation

In mathematics, a hyperboloid is a quadric – a type of surface in three dimensions – . A hyperboloid of revolution of one sheet can be obtained by ... more

Hyperboloid of two sheets equation

In mathematics, a hyperboloid is a quadric – a type of surface in three dimensions – . A hyperboloid of revolution of two sheets can be obtained by ... more

Worksheet 289

Prior to manned space flights, rocket sleds were used to test aircraft, missile equipment, and physiological effects on human subjects at high speeds. They consisted of a platform that was mounted on one or two rails and propelled by several rockets. Calculate the magnitude of force exerted by each rocket, called its thrust T , for the four-rocket propulsion system shown in the Figure below. The sled’s initial acceleration is 49 m/s 2, the mass of the system is 2100 kg, and the force of friction opposing the motion is known to be 650 N.

A sled experiences a rocket thrust that accelerates it to the right.Each rocket creates an identical thrust T . As in other situations where there is only horizontal acceleration, the vertical forces cancel. The ground exerts an upward force N on the system that is equal in magnitude and opposite in direction to its weight,w.The system here is the sled, its rockets, and rider, so none of the forces between these objects are considered. The arrow representing friction ( f ) is drawn larger than scale.
Assumptions: The mass of the Sled remains steady throughout the operation

Strategy

Although there are forces acting vertically and horizontally, we assume the vertical forces cancel since there is no vertical acceleration. This leaves us with only horizontal forces and a simpler one-dimensional problem. Directions are indicated with plus or minus signs, with right taken as the positive direction. See the free-body diagram in the figure.

Solution

Since acceleration, mass, and the force of friction are given, we start with Newton’s second law and look for ways to find the thrust of the engines. Since we have defined the direction of the force and acceleration as acting “to the right,” we need to consider only the magnitudes of these quantities in the calculations. Hence we begin with

Force (Newton's second law)

Fnet is the net force along the horizontal direction, m is the rocket’s mass and a the acceleration.

We can see from the Figure at the top, that the engine thrusts add, while friction opposes the thrust.

Subtraction

Tt is the total thrust from the 4 rockets, Fnet the net force along the horizontal direction and Ff the force of friction.

Finally, since there are 4 rockets, we calculate the thrust that each one provides:

Division

T is the individual Thrust of each engine, b is the number of rocket engines

Reference : OpenStax College,College Physics. OpenStax College. 21 June 2012.
http://openstaxcollege.org/textbooks/college-physics
Creative Commons License : http://creativecommons.org/licenses/by/3.0/

Miller's Rule

In optics, Miller’s rule is an empirical rule which gives an estimate of the order of magnitude of the nonlinear coefficient.

More formally, ... more

Allowable Strength Design Load combination (eq4)

In structural engineering, a structure is a body or combination of pieces of rigid bodies in space to form a fitness system for supporting loads. ... more

Allowable Strength Design Load combination (eq6a)

In structural engineering, a structure is a body or combination of pieces of rigid bodies in space to form a fitness system for supporting loads. ... more

...can't find what you're looking for?

Create a new formula